Size: | |
---|---|
R: | |
Color: | |
Material: | |
Certificate: | |
Availability: | |
Quantity: | |
nb dn15-dn25
S.H.Meters
NBIOT Water Meter Remote Wireless 15mm Brass Body
The nb-iot water meters have low-power design and high-energy batteries.It can work continuously for more than 6 years.
Operation (use) instructions
This product uses the NB-IOT wireless free frequency band to transmit data, and the entire transmission process is automatic. However, it can also be triggered manually for active online. Operation mode: touch the triangular sensing area intermittently (the touch interval is about 2S) until the indicator light is always on. When the indicator light starts to flash, the water meter is online.
Installation & use
1.Water meter with proper calibre should be choosed according to diameter of pipeline at installation site. The expected flow rate should be compatible with the Q1 to Q3 flow of the water meter.
2. The water meter installation must be based on the water meter
dial on the prompt: there is "H" logo for horizontal installation, "V" for vertical installation, the direction of the arrow on the body is consistent with the direction of the pipe flow.
3.The front end and the end of the water meter need to be equipped with a shut-off valve, and the straight pipe section of sufficient length and the same diameter is installed according to the requirements of U5, D3 (5DN, 3DN) to ensure accurate measurement.
4.The impact and vibration of the surrounding environment of the installation site should be prevented, otherwise the water meter will be damaged.
5.The water meter should be protected from excessive stress caused by pipes and fittings. If necessary, install the water meter on the base or bracket. The upper and lower water pipes should be properly fixed to prevent any part from being displaced by the thrust of the water when the water meter is removed or the side is disconnected.
6.Pipeline installation should leave the necessary water meter connection length, when the distance between the two ends of the pipeline exceeds the length of the water meter, the pipeline spacing should be corrected to meet the water meter connection length.
7.The main pipeline should be flushed before installation to prevent stones, sand and other debris from entering the water meter.
8.In order to allow the water meter to work for a long time, the water meter should always be filled with water, it is recommended that the outlet faucet is higher than the water meter by more than 0.5m.
9.When using the water meter, measures should be taken to prevent unfavorable hydraulic conditions (cavitation, surge, water hammer) from damaging the water meter.
10.The water meter should be protected from exposure and freezing, and antifreeze measures should be taken during freezing. The water meter should prevent the external environment from corroding and causing damage to the water meter.
11. During the long-term use of water meters, periodic inspections should be carried out according to local requirements. If there are debris, rust and other deposits in the pipeline blocking the water filter network and affecting the accurate measurement, it must be recalibrated by the designated department, and the user shall not repair the water meter at will.
12.If the water meter is used in a harsh environment, after installing the check valve and venting the gas in the back pipe of the water meter, the water meter rotation cannot be eliminated. The water supply enterprise should consider other methods to solve this problem.
Common faults & causes
Button on flange are broken and damaged. If the spacing is too small, the water meter cannot be installed. If the pipelines at both ends of the water meter are not on the same axis, the pipeline should be corrected
dripping and running water in the pipeline behind the water meter.
3.When there is no data upload on the platform, the administrator needs to go to the site to check the troubleshooting.
Note: The battery of the water meter should be replaced by a professional person, and the user should not replace it by himself.
Disclaimer
If the seal is damaged or incomplete, the company is not responsible. And the company does not bear other responsibilities other than water meters (including but not limited to the responsibility of water metering disputes caused by water meter failure or error.
requirements of the water meter, otherwise the above phenomenon will also occur.
NBIOT Water Meter Remote Wireless 15mm Brass Body
The nb-iot water meters have low-power design and high-energy batteries.It can work continuously for more than 6 years.
Operation (use) instructions
This product uses the NB-IOT wireless free frequency band to transmit data, and the entire transmission process is automatic. However, it can also be triggered manually for active online. Operation mode: touch the triangular sensing area intermittently (the touch interval is about 2S) until the indicator light is always on. When the indicator light starts to flash, the water meter is online.
Installation & use
1.Water meter with proper calibre should be choosed according to diameter of pipeline at installation site. The expected flow rate should be compatible with the Q1 to Q3 flow of the water meter.
2. The water meter installation must be based on the water meter
dial on the prompt: there is "H" logo for horizontal installation, "V" for vertical installation, the direction of the arrow on the body is consistent with the direction of the pipe flow.
3.The front end and the end of the water meter need to be equipped with a shut-off valve, and the straight pipe section of sufficient length and the same diameter is installed according to the requirements of U5, D3 (5DN, 3DN) to ensure accurate measurement.
4.The impact and vibration of the surrounding environment of the installation site should be prevented, otherwise the water meter will be damaged.
5.The water meter should be protected from excessive stress caused by pipes and fittings. If necessary, install the water meter on the base or bracket. The upper and lower water pipes should be properly fixed to prevent any part from being displaced by the thrust of the water when the water meter is removed or the side is disconnected.
6.Pipeline installation should leave the necessary water meter connection length, when the distance between the two ends of the pipeline exceeds the length of the water meter, the pipeline spacing should be corrected to meet the water meter connection length.
7.The main pipeline should be flushed before installation to prevent stones, sand and other debris from entering the water meter.
8.In order to allow the water meter to work for a long time, the water meter should always be filled with water, it is recommended that the outlet faucet is higher than the water meter by more than 0.5m.
9.When using the water meter, measures should be taken to prevent unfavorable hydraulic conditions (cavitation, surge, water hammer) from damaging the water meter.
10.The water meter should be protected from exposure and freezing, and antifreeze measures should be taken during freezing. The water meter should prevent the external environment from corroding and causing damage to the water meter.
11. During the long-term use of water meters, periodic inspections should be carried out according to local requirements. If there are debris, rust and other deposits in the pipeline blocking the water filter network and affecting the accurate measurement, it must be recalibrated by the designated department, and the user shall not repair the water meter at will.
12.If the water meter is used in a harsh environment, after installing the check valve and venting the gas in the back pipe of the water meter, the water meter rotation cannot be eliminated. The water supply enterprise should consider other methods to solve this problem.
Common faults & causes
Button on flange are broken and damaged. If the spacing is too small, the water meter cannot be installed. If the pipelines at both ends of the water meter are not on the same axis, the pipeline should be corrected
dripping and running water in the pipeline behind the water meter.
3.When there is no data upload on the platform, the administrator needs to go to the site to check the troubleshooting.
Note: The battery of the water meter should be replaced by a professional person, and the user should not replace it by himself.
Disclaimer
If the seal is damaged or incomplete, the company is not responsible. And the company does not bear other responsibilities other than water meters (including but not limited to the responsibility of water metering disputes caused by water meter failure or error.
requirements of the water meter, otherwise the above phenomenon will also occur.